Forum General Discussions      Re: ASNT Ethics Violations Posted by: Gerald Newell , E-mail: Address, on August 21, 2008 at 14:42 : In Reply to: Re: ASNT Ethics Violations posted by : Madan L Sharma , E-mail: Address, on August 10, 2008 at 08:09 : I would advise double checking your information against the relevant codes and project specifications. I would also review your information again. If at the end of that review it is incontrovertible then I would contact ASNT through their web site and proceed with instructions for ethics violation reporting. Be aware it is not something to be taken lightly, if in fact he has done as you say, something must be done about it. Any certification be it PCN, AWS, API, ASNT, etc is only as good as the integrity of the person who holds it. If that person lacks the requisite integrity, he or she should rightly lose that certification. Regards, Gerald Newell ASNT III VT, MT, PT, UT AWS CWI ----------- Start Original Message ----------- : These defects,may cause some serious failures.If you know, something is wrong, confront and resolve, with concerned ASNT Level III and end user.Finally the end user is going to be in problem, if any accident happens.You have social responsibility also,please act.ASNT is there to make world safe and support, and weed out the bad elements.You can initiate discussion with ASNT too.But first correct the situation for users.With best wishes. : MLS : : I have a situation where I discovered an ASNT NDT Levle III falsifying NDT results. How can I report him withut getting Project specific. I have undeniable evidence to support this. : : It was not the end useer's fault so I don't want to cause problems for him. : : I gave him and his company ample time to resolve this but they are hoping I will go away apparently. The person accepted NDT data that had bad data in some reports and weld defects in others. He accepted all of them. ------------ End Original Message ------------ Follow Ups: Re: ASNT Ethics Violations John Doe 15:35 Aug-21-2008 (0) Post a Followup: Name: E-Mail: Subject: Comments: ----------- Start Original Message ----------- : I would advise double checking your information against the relevant codes and project specifications. I would also review your information again. If at the end of that review it is incontrovertible then I would contact ASNT through their web site and proceed with instructions for ethics violation reporting. Be aware it is not something to be taken lightly, if in fact he has done as you say, something must be done about it. Any certification be it PCN, AWS, API, ASNT, etc is only as good as the integrity of the person who holds it. If that person lacks the requisite integrity, he or she should rightly lose that certification. : Regards, : Gerald Newell : ASNT III VT, MT, PT, UT : AWS CWI : : : These defects,may cause some serious failures.If you know, something is wrong, confront and resolve, with concerned ASNT Level III and end user.Finally the end user is going to be in problem, if any accident happens.You have social responsibility also,please act.ASNT is there to make world safe and support, and weed out the bad elements.You can initiate discussion with ASNT too.But first correct the situation for users.With best wishes. : : MLS : : : I have a situation where I discovered an ASNT NDT Levle III falsifying NDT results. How can I report him withut getting Project specific. I have undeniable evidence to support this. : : : It was not the end useer's fault so I don't want to cause problems for him. : : : I gave him and his company ample time to resolve this but they are hoping I will go away apparently. The person accepted NDT data that had bad data in some reports and weld defects in others. He accepted all of them. ------------ End Original Message ------------ Optional Link URL: Example: "http://www....html". Alternative write "http://www.ndt.net/wshop/attach/filename.htm" if you transfered a filename.htm via FTP Page Title: is important! Optional Image URL: http://www....gif Attention! Please click the button only once. This may take a moment to process Forum General Discussions Help